Shared:Log
Contents |
18-04-2012 | FORMFINDING
General:
-Modeling rules
-Making algorithm tree (also usable for setup Rhino and grasshopper model)
-Finding diameter and walkable angle of sphere.
-Find rules for connection spheres (how high is placement, how big, how much connected to which spheres)
-Sphere connection diagram.
-Differentiate ribbon
-Small pavilions; width/height; what spheres constitute pavilion.
-where exactly are the snap points for the ribbon?
-Work out ribbon
15-04-2012 | FORMFINDING
http://www.grasshopper3d.com/forum/topics/voronoi-sphere?xg_source=activity
http://www.grasshopper3d.com/forum/topics/balloon-packing-voronoi
General:
-Setup geometry rules
-Algorithm
Pavilion:
-Method of getting 3D model done
-How to de fine the inside of the pavilion
-Rules for inside pavilion (defining relations of spheres to each other and min/max)
-position of spheres inside (what is flat, and what not)
-Making plan of ribbon (width/dimensions)
-continue geometry pavilion
-Rule list for wiki (+tree) (ribbon/ transition/pavilion)
-Sphere list for wiki (pavilion)
30-03-2012 | ARDUINO + RHINO
http://www.instructables.com/id/Arduino-Basics-PIR-Sensor/step4/Further-Projectse/
1st - Tested ones of yesterday (29-03-2012) worked.
2nd - Extra yellow LED added.
3rd - Extra yellow LED and button added
4rd - Motion sensor with LED.
-what component/mode is more important for the system? (fading/push button)
RHINO: -base openings on amount of people +derections (main groups, see all openings as an entrance based on routing)
-Parameter tree (start pavilion min. 5m from obstacle, etc.)
Parameter list:
-people (directions/amount)
-obstacles on the way ( min. + max. distance from obstacle)
-sunlights (how much let in without compromising system)
-width of ribbon
-Proximity to water
TASKS
Romain:
-Rhino model
-Pavilion skin +structure
-Questions Log 29-03-12
-Phone program
-integration of whole model
-More parameters
Magda
-rhino model-ribbon where is? Draw in the diff layer
-questions log 29-03
-think about skin and structure – that applies both to ribbon and pavilion
-parameter tree – algorithm based on elements of parameetric design
-arduino –setup of iphone intreface
-integration of lighting into the ribbon/system
29-03-2012 | ARDUINO
http://www.youtube.com/watch?feature=endscreen&v=6mHnhLs8Dg8&NR=1
Sequence RGB LEDS with button
Iphone control
LED circuit +button
-Arduino guidelines
-Just 1LED with button
-Generative architecture
http://flickriver.com/photos/brucesterling/sets/72157616511871362/
http://sojamo.tumblr.com/post/140563395/biothing-founded-by-alisa-andrasek-in-2001
http://www.grasshopper3d.com/photo/mesh-relaxation-n-inflation-3?context=latest
http://27thdesign.com/2012/03/04/parametric-design-and-generative-architecture/
1st - Not working.
2nd - worked with touching resistor instead of button (broken breadboard)
-Extend system to all snap point, instead of first connecting snap points to Ondina pavilion.
-Define communication between snap points Is the system totally centralized?
-Defining virtual/physical snappoints.
-Material boardwalk/pavilions
-Define elevations and situation/route of the bordwalk.
-Define Lighting objects within boardwalk.
-How does the lighting system work (in both ways)?
-How do the little interfaces work and look like?
-What is the material (sort of predefined shape projected over main-shape.. new sort of ‘brick’?!)’ and construction
-Interface integrated well enough in architecture?!
-Define all parameters which influence pavilion.. (route people, sun, ramp,.. )
28-03-2012 | ARDUINO
http://www.youtube.com/watch?feature=endscreen&NR=1&v=WHc4BWykXvI
http://www.youtube.com/watch?v=G_dOMheklOk
Tested 3 LED sequence blinking, without button.
-Examples button and LED sequence
-Things we want to test;
1)sequence of pushing buttons
2)two states of blinking
3)intensity (brightness), blinking state to modes of sytem
4)moving sensor test to modes
-Uploading photos and videos on youtube